GTM Owners Club Forum http://www.gtmdrivers.com/forum/ |
|
coilover brackets http://www.gtmdrivers.com/forum/coilover-brackets-t3601-30.html |
Page 3 of 3 |
Author: | PEEPS [ Tue Oct 31, 2017 7:23 pm ] |
Post subject: | Re: coilover brackets |
Hi J, yes I can weld them for you, only takes 10 minutes so no extra cost. Peter. |
Author: | jaybee [ Tue Oct 31, 2017 8:55 pm ] |
Post subject: | Re: coilover brackets |
PEEPS wrote: Hi J, yes I can weld them for you, only takes 10 minutes so no extra cost. Peter. Peter You have PM J. |
Author: | jaybee [ Sat Jan 06, 2018 5:53 pm ] |
Post subject: | Re: coilover brackets |
PEEPS wrote: I have used the MGF rear anti roll bar which fits on brackets hung from the rear subframe mounts. There is a tiny bit of clearance needed where it bends but it should work fine. Though I have used the MGF rear suspension setup. You will see what I mean. Attachment: engine in.JPG Peter Did you have any clearance issues at the body tub mountings for the MGF tie bar set up? Thanks John |
Author: | roger [ Sat Jan 06, 2018 6:34 pm ] |
Post subject: | Re: coilover brackets |
Hi I take it these would fit a Metro/R100 front subframe? If so I would be interested in an assembled pair if they are still available? |
Author: | PEEPS [ Mon Jan 08, 2018 2:26 pm ] | |||
Post subject: | Re: coilover brackets | |||
Attachment: subframe bracket.JPG [ 318.71 KiB | Viewed 8852 times ] Using the MGF subframe you will need to cut off the outside brackets as shown in the photo. The subframe will then fit into the tub mounts using the long bolt shown. The tie bar is not affected.
|
Author: | jaybee [ Tue Jan 09, 2018 6:20 am ] |
Post subject: | Re: coilover brackets |
Peter Perfect, as I was was concerned that the front trailing arm mount would foul and judging by some of your other photos, the TF subframe could be a possibility too. Cheers John |
Author: | IAN 51 [ Wed Oct 24, 2018 2:47 pm ] |
Post subject: | Re: coilover brackets |
Hi i have just bought my first GTM K3 and im looking to ditch the hydragas and move over to coilovers are these brackets still avaliable. Thanks Ian |
Author: | PEEPS [ Wed Oct 24, 2018 3:25 pm ] |
Post subject: | Re: coilover brackets |
Hi Ian, Yes they are, i've just had some more cut so they will be available. £30.00 per axle set + £12.00 postage. The backs are the same as the fronts but with the extra bracket on for the torque tube fixing. Peter. |
Author: | IAN 51 [ Wed Oct 24, 2018 3:57 pm ] |
Post subject: | Re: coilover brackets |
Excellent Peter put me down for a full car set and the best way of paying you for them |
Author: | catsam [ Sun Oct 28, 2018 3:07 pm ] |
Post subject: | Re: coilover brackets |
peter soon all the k3 will have your coilover brackets on them |
Author: | catsam [ Sun Nov 04, 2018 11:54 am ] |
Post subject: | Re: coilover brackets |
hi peter on the front passenger side do you no if the coilover bracket hits the heater fan box thanks paul |
Author: | jaybee [ Sun Nov 04, 2018 7:20 pm ] |
Post subject: | Re: coilover brackets |
Paul. When I built up my K3 using PEEPS brackets, there was clearance for the heater box, as the height is only a few mm taller than the hydragas spheres but sadly I cannot find a photo showing it fitted. For reference, the MGTF front strut towers are taller than PEEPS brackets and there was plenty of clearance as shown on my K3 thread. J. |
Author: | catsam [ Sun Nov 04, 2018 8:06 pm ] |
Post subject: | Re: coilover brackets |
hi thanks that will help im having fun trying to get my ARB to have some clearance. i have a plan just need to see if will work thanks paul |
Author: | Chops [ Tue Jun 25, 2019 6:27 pm ] |
Post subject: | Re: coilover brackets |
Are these coil over brackets still available? |
Page 3 of 3 | All times are UTC [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |