GTM Owners Club Forum http://www.gtmdrivers.com/forum/ |
|
Just Got Myself A 1995 1.4 Twin Cam K3 http://www.gtmdrivers.com/forum/just-got-myself-a-1995-1-4-twin-cam-k3-t3890-60.html |
Page 5 of 5 |
Author: | jaybee [ Mon Jun 25, 2018 8:08 pm ] |
Post subject: | Re: Just Got Myself A 1995 1.4 Twin Cam K3 |
Shiny J. |
Author: | jaybee [ Wed Jun 27, 2018 9:34 am ] |
Post subject: | Re: Just Got Myself A 1995 1.4 Twin Cam K3 |
Well, I had a little play last night and have hit a problem with the rear clam frame fouling on the MGF rear anti roll bar - I originally took the ARB off to allow me space to fit the coil over set up and when I offered it back up last night, it fouls on the rear clam frame; therefore, has anyone managed to fit the ARB without serious butchery of the rear metalwork? J. |
Author: | tonygerrard(1049) [ Wed Jun 27, 2018 9:40 am ] |
Post subject: | Re: Just Got Myself A 1995 1.4 Twin Cam K3 |
Hi Jaybee, Where did you get your nice shiny manifold and is there any difference to 1.6 & 1.8? |
Author: | jaybee [ Wed Jun 27, 2018 9:51 am ] |
Post subject: | Re: Just Got Myself A 1995 1.4 Twin Cam K3 |
tonygerrard(1049) wrote: Hi Jaybee, Where did you get your nice shiny manifold and is there any difference to 1.6 & 1.8? It was thrown in as part of the deal for me to buy the full MGF rear end and as far as I am aware, it does all K-Series engines. I was looking at this one and they have dropped the price as tad https://www.ebay.co.uk/itm/STAINLESS-ST ... SwZ65a6HxS J. |
Author: | jaybee [ Mon Jul 02, 2018 11:07 am ] |
Post subject: | Re: Just Got Myself A 1995 1.4 Twin Cam K3 |
It’s been too hot to do much in the last week or so, but managed a few hours last night and fitted the coil over brackets, GAZ dampers and Faulkner springs to then rear of the car after much jittery pokery - what should have taken an hour too 3 times that but I got there in the end. Ready to go on, but I ran out of time due to the fact that I need to disconnect all engine and gearbox mounts to tilt the rear set up enough to squeeze in........... Hopefully I can make this fit too! J. |
Author: | PEEPS [ Mon Jul 02, 2018 4:22 pm ] | ||
Post subject: | Re: Just Got Myself A 1995 1.4 Twin Cam K3 | ||
This is how it looked with the cat installed. It pushed the box out too far and would have needed surgery to the rear clam so I made my own. Peeps.
|
Author: | jaybee [ Mon Jul 02, 2018 8:08 pm ] |
Post subject: | Re: Just Got Myself A 1995 1.4 Twin Cam K3 |
PEEPS wrote: This is how it looked with the cat installed. It pushed the box out too far and would have needed surgery to the rear clam so I made my own. Peeps. Peter. Many thanks for that, it’ll save me a lot of hassle. Did you manage to get the rear clam frame to fit properly with the rear anti roll bar in place? J. |
Author: | PEEPS [ Tue Jul 03, 2018 10:44 am ] | ||
Post subject: | Re: Just Got Myself A 1995 1.4 Twin Cam K3 | ||
Hi J, No, I did away with the original box section horror, fastened the arb to the mount brackets as shown and made my own adjustable clam pivot plates that bolted directly to the subframe.
|
Author: | jaybee [ Tue Jul 03, 2018 11:41 am ] |
Post subject: | Re: Just Got Myself A 1995 1.4 Twin Cam K3 |
PEEPS wrote: Hi J, No, I did away with the original box section horror, fastened the arb to the mount brackets as shown and made my own adjustable clam pivot plates that bolted directly to the subframe. Thanks!! Do you have any photos of the clam mounts? J. |
Author: | PEEPS [ Tue Jul 03, 2018 3:19 pm ] | ||||
Post subject: | Re: Just Got Myself A 1995 1.4 Twin Cam K3 | ||||
Hi J, The triangular piece that takes the pivots originally was hanging off so I removed it, bonded in a couple of stiffeners and then bonded in a couple of stainless brackets which then lined up with the subframe brackets. These gave me 30mm adjustment up and down and in and out. I will see if I can find the original drawings for the subframe mounts, I had these laser cut (surprise!) and welded one into an 'L' shape for the other to bolt to. Peter.
|
Author: | jaybee [ Mon Jul 09, 2018 3:44 pm ] |
Post subject: | Re: Just Got Myself A 1995 1.4 Twin Cam K3 |
Thanks for the photos Peter I managed to find an hour today and fitted the Faulkner 7" 275lbs springs to the standard TF front dampers and the look is much better now. J |
Page 5 of 5 | All times are UTC [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |